The BYD Shark 6 in its Project Shark livery: matt black and silver, with the OL mark and tyre-track graphics down the side
Livery on

Project
Shark

A BYD Shark 6 Performance going from showroom standard to fully kitted. The first kit is on, and now it wears its Project Shark livery. Follow us as we build.

VehicleBYD Shark 6 Performance
DrivetrainPlug-in hybrid
LiveryMatt black & silver
StatusBuild under way
350 kWCombined system output
700 Nm
29,6 kWhLFP Blade battery
Up to 80 km on electric
3 500 kgBraked towing
2,0 T petrol + a motor on each axle
230 mmGround clearance
0–100 km/h in 5,5 s

Before & after // same bakkie

Same bakkie.
Now wrapped.

Before is the Shark as it was collected. Now is the same bakkie today: Tough Dog suspension, an Artav nudge bar carrying Lightforce Beast driving lights, a Hamer 4x4 sliding cover over the tub, all-terrain tyres on ROH wheels, Takla covers in the cabin, and the Project Shark livery.

Front on

The Shark 6 front on, as collected, with the standard front end
Before
The wrapped Shark 6 front on, with the nudge bar and Lightforce Beast driving lights
Now

Side on

The Shark 6 side on, as collected, in standard black
Before
The Shark 6 side on in its livery, with the OL mark, tyre-track graphics and the partner panel on the tub
Now

Rear three-quarter

The Shark 6 from the rear, as collected, with the tub open
Before
The wrapped Shark 6 from the rear, with the Hamer 4x4 sliding cover closed and Tough Dog on the tailgate
Now

The brief // why this vehicle

A bakkie that brings
its own power

Every fleet vehicle we build teaches us something we can pass on. The 76 taught us leaf-sprung load. The Hilux taught us protection packages. This one is different: it is the first plug-in hybrid in the fleet, and it arrives already solving a problem our customers normally come to us for.

The Shark 6 carries a 29,6 kWh battery and a power outlet in the tub. That is a camp kitchen, a compressor and a fridge running off the vehicle before we fit a single accessory. So the question this build answers is not "what can we bolt on". It is "what still earns its place when the bakkie already does half the job".

The rest of the brief is less familiar. The suspension is independent at all four corners. There is no leaf pack, and none of the reflexes that come from having fitted the same kit to the same bakkie a hundred times. The aftermarket has moved quicker than most people realise here: Tough Dog already builds a kit specifically for this vehicle, and it is now on ours.

Vehicle figures are the manufacturer's published specification. We correct anything here that turns out to be wrong.

Where it stands // we publish as we fit

We publish
as we fit

Each piece goes up here once it is on the bakkie, with the parts named and nothing guessed.

FittedNovember 2026

Interior

The cabin is done. Takla covered the front seats and the rear bench, with the OL mark on the front headrests, and added a dashboard cover and covers for the centre console.

The backs of the front seats carry storage, with sleeves and a zip pouch within reach of the rear seats. The console covers are cut around every tray, vent and switch.

  • Takla seat covers
  • Takla dashboard cover
  • Takla centre console covers
The Shark's front seats in Takla covers, with the Opposite Lock mark on the headrest
FittedOctober 2026

Livery

The Shark is wrapped. Matt black and silver, with tyre tracks and the OL mark down the side, Lightforce across the bonnet, Tough Dog on the tailgate and the OL monogram on the roof.

The tub panels carry the partner brands we work with on this build, and a Scan the Build QR code.

  • Project Shark livery
The silver tub panel carrying the Opposite Lock logo, partner logos and a Scan the Build QR code
FittedSeptember 2026

Rubber

The road tyres it came on are off. It now runs all-terrain tyres from Tyremart Centurion CBD on a set of ROH wheels from 4x4 Wholesalers Africa. They are the only part of this build that actually touches the ground, and the part that decides whether the rest of it gets used.

Everything changes with tyres: grip on gravel, how the bakkie sits, what the suspension has to deal with. We will say more about how they behave once the vehicle has done some distance on them, rather than on the day they went on.

  • All-terrain tyres · Tyremart Centurion CBD
  • ROH wheels · 4x4 Wholesalers Africa
The Shark 6 on its new all-terrain tyres and wheels
FittedSeptember 2026

Stance

The suspension is Tough Dog, a kit engineered specifically for the Shark and not adapted from something else. Foam Cell struts up front, nine-stage adjustable shocks at the rear, and coils to suit.

The rear is where this vehicle differs from everything else in the fleet. There is no leaf pack to re-arch or replace: it is independent, on coils, with an electric motor on the axle. Adjustable damping matters more here than it does on a conventional bakkie, because the setup has to work both unladen around town and loaded for a trip, and we can dial it rather than guess it.

  • Tough Dog Foam Cell front struts
  • Tough Dog 9-stage adjustable rear
  • Tough Dog coils
A Tough Dog front strut and coil fitted to the Shark
FittedSeptember 2026

Front end

An Artav nudge bar is on the front, and it carries the Lightforce Beast driving lights, wired in on their own looms.

Power is the other half of this one. The Shark already has a power outlet in the tub, running off its 29,6 kWh battery. So the honest question is what a 12 V system still adds here, and we would rather answer that after living with the vehicle than before.

  • Artav nudge bar
  • Lightforce Beast driving lights
  • Lightforce Beast wiring looms
  • 12 V system · under review
Lightforce Beast driving lights mounted on the nudge bar
FittedSeptember 2026

Load

The tub is now closed under a Hamer 4x4 sliding cover. It keeps the load bed covered and out of sight, and slides back towards the cab when you need the full tub.

  • Hamer 4x4 sliding cover
The Hamer 4x4 sliding cover closed over the Shark's tub
Collected15 September 2026

Collected

Darrell collected the Shark in black, double cab, standard off the showroom floor. Before anything was fitted we did the unglamorous part: learning where the battery, the high-voltage runs and the rear motor sit, so that nothing gets drilled, clamped or bolted where it should not be.

On a ladder-frame diesel bakkie we know where it is safe to mount a step, a bracket or a winch. On a hybrid with a floor-mounted pack and a motor on the rear axle, we find out first and fit second.

Darrell with the black Shark 6 on the day he collected it

Also on the list // not yet specified

The rest gets
decided as we go

These are the areas still open. What goes into each one gets chosen against the vehicle rather than off a catalogue, and several may be fitted together depending on what a centre can take on in one visit.

Protection

Underbody, sides and steps

Storage

Drawers and tub organisation

Recovery

Points, gear and stowage

Touring

Camp and long-distance kit

The kit // confirmed only

What goes on it,
named properly

A part only appears on this board once it is ordered or fitted.

Suspension Fitted

Stance

Tough Dog Foam Cell front · 9-stage adjustable rear · coils to suit

Shop Tough Dog →

Front end Fitted

Nudge bar

Artav nudge bar, carrying the driving lights

Load Fitted

Tub cover

Hamer 4x4 sliding cover

Rubber Fitted

Tyres

All-terrain tyres from Tyremart Centurion CBD · ROH wheels from 4x4 Wholesalers Africa

Livery Fitted

Wrap

Project Shark livery · matt black and silver

Interior Fitted

Cabin

Takla seat covers · dashboard cover · centre console covers

Build partners // who did what

Built with
partners

The Tough Dog suspension and Lightforce lights are Opposite Lock lines. These are the partners whose work is on this bakkie too. We add each one as the work is done.

Takla

Seat covers · dashboard cover · centre console covers

Hamer 4x4

Sliding load bin cover

Tyremart

All-terrain tyres · Centurion CBD

Artav

Nudge bar

4x4 Wholesalers Africa

ROH wheels

Your build // starts the same way

Build yours

We are doing this one in the open so you can see how the decisions get made. When you are ready to make yours, get in touch and we will help you spec it against your vehicle and what you actually do with it.

Enquire about this product

We use these details only to reply to your enquiry about this product. See our privacy policy for how we look after them.